$18.99 - $24.99
- Made to fit crank spindles and press-fit Mid BB frames. - Simple and easy to install. - Includes an assortment of spacers to optimize chainline and crank clearance. - Odyssey 6061-T6 aluminum dust spacer included.
- 4140 Chromoly - 3 Possible peg positions for longer peg life - 14mm with 3/8-inch adapters included - 4 inches (length) x 1-3/8 inches (outer diameter) - Sold in pairs - 8.75 oz (17.5 oz for a pair)
This is Tom Dugan’s all new signature sprocket. In addition to its classic look, the Fang increases in thickness towards the center of the sprocket for increased strength. - 7075 Aluminum - Sweet machining
The Antigram is a 36-H rear hub that is strong, light and reasonably priced with in-bound axle bolts that is both RHD/LHD switchable and guard compatible. SPECS - 2014-T6 forged aluminum hub shell - 6903RS sealed cartridge ball bearings - 9-T driver with 3-Pawn independent springs design and precision caged needle bearings - RHD/LHD switchable WEIGHTS - With 14mm Chromoly Axle: 14.5oz / 411g - MEASUREMENTS Drive Side - Effective Flange Diameter: 49mm - Non-Drive Side Effective Flange Diameter: 49mm - Drive Side Flange to Center Distance: 30mm - Non-Drive Side Flange to Center Distance: 30mm
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable too. The Ghost Pad addresses the hassles of brake pad installation by eliminating the traditional dome shaped washers used for toe-in. The pad improves stiffness by building the toe-in into the pad shape and utilizing a solid extruded aluminum frame at its core. The Ghost Pad’s assembly consists of simply lining it up with the rim and tightening down an M6 female bolt. Comes stock on the Springfield brake. SPECS Hardware: - In-bound bolt, 5mm Hex Key, M6x1.0 Thread - Pad Material: Black (standard) or Clear Rubber (Soft) - Weight: 1.0oz / 28g (pair)
When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.
The M2 lever works with a single cable or Odyssey’s patented dual cable system. The M2 cable system improves braking power for GYRO users. - Right hand only (works flipped on the left) - M2 specific upper cable and single cable coupler included.
The Monolever was an instant classic and has become a clear favorite with pro riders around the world because of its familiar feel, smooth edges and variety of handle options.
Odyssey's custom-designed Par Ends come standard with all of their grips. Its special plastic composite will not shatter like cheap bar ends do, and they’re very lightweight. The Par End is a combination of the over-the-bar-style cap and the inside-the-bar-style to prevent the inner portion from blowing out like it does on ordinary press-fit bar ends. Comes stock on all of Odyssey's grips.
It’s a traditional straight up pivotal design with a 200mm length.
Designed specifically for use with Odyssey's Quartet FRONT or REAR hubs. SPECS - Forged from 7075-T6 aluminum for greater strength and durability - Steel insert prevents guard deformation, prolonging bearing life
The Slim by Four is a BMX-specific brake pad with a symmetrical shape designed for both forwards and backwards braking. A custom inner frame helps to stiffen the pad and prevents excessive braking power from being lost to flex. SPECS - Clear and Gum colored “Soft” compound pads provide extra grip on powder coated rims. - Black “Normal” compound Slim-By-Four pads are the most popular pad choice for most riders.
$13.99 - $16.99
One of the most successful and popular pedals, and for good reason with its extremely simple, lightweight, inexpensive and famously durable plastic-bodied design. Often duplicated but never replicated. - High-strength plastic composite
Radio PRO Leon Hoppe's signature 47 Sprocket Guard is made to take a real beating. Featuring an integrated 8mm thick alloy guard and a robust CNC machined construction; if you're looking to get tech as hell and not break your chain, we suggest investing in one of these.
In BMX racing, that first sprint from the gate is the most important part of the race. Shimano knows this, so their DXR cranks are unbelievably stiff, perfect for getting out in front for the holeshot. They borrow Hollowtech II technology from the Saint downhill cranks to make them rigid, light and super tough. They sport a narrow Q factor for smooth pedaling and steel pedal inserts for durability. When 2nd place just won't do, DXR is the answer.
Check out the dinosaur skin-like texture of WeThePeople's Raptor grips! Like a raptor, you can wrap your claws around these grips and let the good times roll. The soft, VEX rubber compounds conforms perfectly to your hand, and holds up great to long days on the bike. • 150mm Long, 27.8mm Diameter • 30 durometer rubber • Low flange design • Includes WeThePeople nylon barends
$77.99 - $79.99
A beast like pro rider Dillon Lloyd needed a bar built to withstand the biggest drops and burliest of crashes. The Buck bar is one of the first bars in BMX to utilize the new 25.4mm clamping technology, allowing for a stronger, stiffer bar that a rider like Dillon can have full confidence in, without having to worry about it slipping or breaking when things get rough. WeThePeople used time-tested "M2" heat-treated, 4130-chromoly tubing and Dillon's own geometry to create this ultra-dependable set of bars you can get "Buck" with. - Tubing: 7/8" multiple butted - Easy-cut marks on the end of the bars - Dual radius bends for extra strength - Backsweep: 11-degrees - Upsweep: 1.5-degrees - Weight: 22.2mm bar: 895g (31.5oz/1.97lbs), 25.4mm bar: 925g (32.48oz/2.03lbs)
A total redesign of Odyssey's popular MDS sprocket. With a built-in full guard, this sprocket lives up to its name, helping to protect your chain from anything you can throw at it. Sprocket thickness increases towards the guard area for greater strength. Compatible with all chain widths. - 7075 Aluminum
$49.99 - $50.99
The Pathfinder Sprocket is much thicker than anything else WeThePeople had made before. Its 8mm-thick beef and unique 9 sided design integrates the sprocket mounting location into the spoke pattern, resulting in a super-clean looking sprocket with plenty of strength and longevity, even for the most savage rider out there.
- Sold in pairs. - Allen wrench included.
Tom likes to ride fast and go very high. These tires were designed to help him do just that. With a fast center tread, these tires are made for park, street and even dirt too. The side profile is reminiscent of a motorcycle tire as well, which is a nod to Tom’s motorcycle lovin’ ways.
Odyssey's 41-Thermal forks quickly established a reputation for strength and quality when they originally introduced them in 1999, and they have since gone on to change the standards that all forks are judged by. Their new R-Series forks continue this tradition. FEATURES - Fully redesigned. - Laboratory tested and team proven. - New, custom, seamless, tapered, butted and specially formed leg tube shaping for improved grind and guard clearance. - All-new steerer tube design improves fatigue strength and includes a built-in, integrated, lower headset seat race. - New, optimized, 4mm dropout shape for grind and peg clearance. - Updated 7075-T6 pre-load bolt - Proven 41-Thermal® processed 4130 chromoly - Legendary lifetime replacement warranty SPECS - 32mm traditional offset - 3/8” axle slots only Starting at 1lb 15.2oz (885 grams)
Odyssey's Air Supply tubes are specifically sized to fit modern BMX tires, and they are manufactured with a stronger emphasis on quality versus simply chasing the lowest possible price. On average, the Air Supply BMX tube retains air significantly longer than others currently available on the market. This is down to both the rubber that is used, and because of strict quality control during manufacturing. It is normal to assume that a “tube is a tube,” but a higher quality tube will always last longer than a cheap tube during comparable everyday use.
WeThePeople's Team Pivotal seatpost is made from 6061 aluminum for a perfect blend of strength and weight savings. It works with all Pivotal seats and it's 200mm long for plenty of adjustability.
In addition to updating Aaron’s tire, Odyssey also wanted to update his signature grip. The updated “Boss” grip features a low profile block pattern which will match his tire, and comes in at 158mm. These will feel similar to his original grip, but improved and with all new styling.
Odyssey racing spokes use butting dimensions that are tailor-made for BMX racing, and they’re still strong enough to handle some light street riding too. You’ll save roughly an ounce per wheel on 36’s. Only the best stainless steel has been used, and the gradual butting transitions are ideal for the stresses that a 20-inch wheel has to endure. - Proprietary professional-grade stainless steel. - BMX specific butting transition dimensions.
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable. The Springfield brake drops the two ordinary (and confusing) brake springs and replaces them with one central spring that applies the same force to each arm, requiring no additional adjustment. This makes assembly incredibly easy–just bolt it on and go. The brake arms are designed to maximize stiffness and save weight without adding excessive cost. By die-casting the arms and using shared tooling to make each side, the Springfield meets all of the original design goals, resulting in a very powerful and affordable brake.
Using Odyssey's popular TL48 stem as a springboard, Broc Raiford's signature RAFT stem is a classic top load design. FEATURES - Six bolt clamping configuration - Headset pre-load bolt recess (32mm diameter) - 6061-T6 aluminum, CNC machined
Shimano's DXR V-Brake Levers are the choice of the pros, from the Olympics to the local race scene. They use a 2-finger design with Shimano's proven Super Linear Response system that gives you great power and feel with little effort.
$67.99 - $74.99
A long running standard, the Hazard Lite is revered because of its strength, lightweight and affordable price. Constantly imitated but never matched in quality or reliability, the Hazard Lite is used regularly by pro-level riders–even the ones that are being paid to ride something else. SPECS - 6000 series aluminum - 32mm wide - 17mm tall 36H - 20-inch version (ERD: 390mm) - 24? version (ERD: 486mm)
Page 1 of 3 Next page